Bob’s Machine Shop’s convertable manual MJ5 jack plate is actually 4 units in one! It can be 2.5″ setback or 5″ setback. And it can have a straight or negative 6 degree wedge.
They are anodized black for race oriented looks. Easy adjustments are made on the side of the jack plate.
5-inch Offset with 6-Degree Wedge
Jacking bolts- allow motor to be moved to any height. No need to take boat out of the water.
Offset- positions motor 5 1/2 inches behind transom. This allows prop to run in cleaner water, away from the turbulence and bubbles created by the hull. This helps stop slippage of prop, and helps stop torque in steering wheel at high speeds.
Trim-In- this allows motor to be trimmed in or down 6 degrees more than if mounted flat on transom. Helps stop low speed porpoising. Balance load better.
Light-weight- approximately 20lbs., constructed of aircraft grade aluminum and stainless steel.
Anodized- anodized black finish to prevent corrosion. Anodize also lets paint stick to aluminum if painting is preferred.
Narrow designed- only inches wide, make this plate possible to fit the narrowest of transoms.
Fits V-6- pre-drilled to fit all late model V-6’s. Can be modified to fit any size outboard.
Converting the new 4 in 1 is as easy as dropping anchor!
Adjustable plates turn 180 degrees and switch sides, then bolt in place.
Overall width: 17-7/8”(45.3cm)
Overall height:14”(35.5cm).
All manual jac plates have 2 ½“(6.3cm) of lift built in and 4”(10.1cm) of adjustable lift.
Lifetime warranty on structure
Made in USA, in our own factory in Tampa, Florida
Rated for 200HP, V6 motors (heavier should use Extreme series)
Convertable MJ5 5″setback manual jack plate
€462.00
Bob’s Machine Shop’s manual jack plates are our lightest and cheapest jack plate option!
€462
Descrizione
Bob’s Machine Shop’s convertable manual MJ5 jack plate is actually 4 units in one! It can be 2.5″ setback or 5″ setback. And it can have a straight or negative 6 degree wedge.
They are anodized black for race oriented looks. Easy adjustments are made on the side of the jack plate.
5-inch Offset with 6-Degree Wedge
Jacking bolts- allow motor to be moved to any height. No need to take boat out of the water.
Offset- positions motor 5 1/2 inches behind transom. This allows prop to run in cleaner water, away from the turbulence and bubbles created by the hull. This helps stop slippage of prop, and helps stop torque in steering wheel at high speeds.
Trim-In- this allows motor to be trimmed in or down 6 degrees more than if mounted flat on transom. Helps stop low speed porpoising. Balance load better.
Light-weight- approximately 20lbs., constructed of aircraft grade aluminum and stainless steel.
Anodized- anodized black finish to prevent corrosion. Anodize also lets paint stick to aluminum if painting is preferred.
Narrow designed- only inches wide, make this plate possible to fit the narrowest of transoms.
Fits V-6- pre-drilled to fit all late model V-6’s. Can be modified to fit any size outboard.
Converting the new 4 in 1 is as easy as dropping anchor!
Adjustable plates turn 180 degrees and switch sides, then bolt in place.
Overall width: 17-7/8”(45.3cm)
Overall height:14”(35.5cm).
All manual jac plates have 2 ½“(6.3cm) of lift built in and 4”(10.1cm) of adjustable lift.
Lifetime warranty on structure
Made in USA, in our own factory in Tampa, Florida
Rated for 200HP, V6 motors (heavier should use Extreme series)
€462